Kauppasivu
Stormworks: Build and Rescue
Kaikki Keskustelut Kuvakaappaukset Taideteokset Suoratoistot Videot Workshop Uutiset Oppaat Arvostelut

Stormworks: Build and Rescue

Kauppasivu
Stormworks: Build and Rescue >  Workshop > Käyttäjän Uran_Wind Workshop > ZE 6-gear Auto/Manual Transmission
ZE 6-gear Auto/Manual Transmission
Kuvaus Keskustelut0 Kommentit36 Muutokset
36 kommenttia
< >
Lucky Tiny Storm 8.3. klo 10.37 
The gear start changing too early wich causes the wheels to slip.
Uran_Wind  [tekijä] 31.12.2024 klo 11.57 
Check if all gear ratios are correct, and make sure the engine has enough power for higher gears.
Alfraido 30.12.2024 klo 11.41 
I believe i have everything connected correctly, but i am facing a problem where it runs fine in neutral, first, second (where it reaches 29mph top speed) and then the engine immediately stalls and cannot run with gears 3 4 or 5. Any idea on what could be causing that?
Uran_Wind  [tekijä] 30.12.2024 klo 5.03 
Insert an extra gearbox between the torque meter and wheels, and adjust its gear ratio.
Alfraido 29.12.2024 klo 20.51 
How would i adjust the ratio to get 29mph top speed, or any certain speed? It seems a bit dumb to randomly change ratios until a speed is reached (which i have not yet achieved)
Uran_Wind  [tekijä] 28.12.2024 klo 11.18 
Yes, you can use all items from the workshop by default, unless the author explicitly prohibits it.
My_Name_is_Bear 28.12.2024 klo 8.46 
can i use this on my creations if i link it?
dsed22 14.12.2024 klo 17.08 
ive been trying to make a gtr skyline but only revers and one gear work also if you run the clutch trrough a elec motor u go faster
DerAtomherbst 1.12.2024 klo 18.47 
I've been tryna make an MC that allows this MC to be controlled by a throttle lever

I kinda have it but it's funky and really weird
Ω Compu 26.11.2024 klo 7.48 
can an option for number of reverse gears be added? would be useful for tractors
ghost 11.11.2024 klo 8.58 
If you put on 3 gear
off 9:5 on 3:2
You'll have more speed
Uran_Wind  [tekijä] 10.8.2024 klo 12.43 
Make sure you connected the RPS node from the torque meter, installed after the 4-th gearbox.
Weird Uncle 10.8.2024 klo 12.35 
it generally does not seem to work, even though it seems set up correctly. I am unable to get it to shift when in auto, even though the RPS well exceeds its shifting point
Weird Uncle 10.8.2024 klo 2.00 
no matter what I try with any of my vehicles, there's always too much wheel spin due to the transmission, causing the wheels to spin into a burnout. The only way to fix it is by limiting the power output through the clutch, but it has to be limited so much that my max speed always ends up being a crawl.
LiefErik 97 22.1.2024 klo 9.44 
I really like this transmission, the setup is compact but highly versatile. I would like if it had a built in clutch controller though.
F25 Key 24.5.2023 klo 4.10 
can you add an option to make the default mode park like in the full drive controller?
Graztoked 31.3.2023 klo 15.48 
Ill make that adjustment with the visual indicators that might be what was confusing me. Thanks a bunch! ill delete my boat spam to keep ur amasing controller comments clean!
Uran_Wind  [tekijä] 30.3.2023 klo 23.49 
All gears and reverse works fine, the low gear has indicator value of 2 instead of 1.
Uran_Wind  [tekijä] 29.3.2023 klo 23.26 
Make sure all gearboxes and torque meter are assembled and oriented in correct order.
Shaquille Oatmeal 4.11.2022 klo 7.00 
ok thanks
Uran_Wind  [tekijä] 4.11.2022 klo 5.35 
Yes, probably. Try to increase the clutch smoothly.
Shaquille Oatmeal 4.11.2022 klo 4.44 
so it could be that my car is too heavy?
Uran_Wind  [tekijä] 3.11.2022 klo 23.49 
Engine can stall if the torque load is too high even on first gear, although its overall gear ratio is 0.14 . Anyway, check that the directions and ratios of all gearboxes are correct.
Shaquille Oatmeal 3.11.2022 klo 6.17 
i put this on a car im reworking and when i put it in gear and put the clutch to 1, the engine slows down until it stalls, maybe the OFF Ratios are still not well enough geared down? any alternative gear ratios you know of?
Uran_Wind  [tekijä] 5.4.2022 klo 10.26 
It is an optional node for indicationg the current mode or gear, you can left it unconnected.
That Guy 5.4.2022 klo 2.57 
how do you set up Auto mode | current gear
Uran_Wind  [tekijä] 29.1.2022 klo 10.54 
Fixed, also clutch value should be 1 during acceleration in order to shift gears correctly.
muhammedexplosive911 29.1.2022 klo 10.06 
doesnt change from gear 3 to 4 when reaches desired rps
OOM-7 22.2.2021 klo 23.35 
How do I display gears on 7 segments in automatic mode?
Uran_Wind  [tekijä] 7.1.2021 klo 22.02 
This is the controller only for the set of gearboxes, and it dont have the clutch control since it may depends on preferences of car handling. You may use other controller for the clutch, or just connect the ws seat axis to it.
TUSK771 7.1.2021 klo 18.10 
I'm using this Micro on a vehicle, not sure where to connect the clutch, there is the Auto/ current left open ? when i try in manual. engine keep stalling ?
Uran_Wind  [tekijä] 17.10.2020 klo 1.41 
It is only the gearbox controller without a clutch or brakes, and the gear ratio at N is similar to the ratio of first gear. So, add the clutch which disengages at N. Also you may use my full-fledged car drive controller having all basic features.
umtiti 17.10.2020 klo 1.14 
yes i fixed it now. Now the vehicle does not stop at N
Uran_Wind  [tekijä] 16.10.2020 klo 17.08 
Did you set the correct gear ratio on the 4-th gearbox and switch the gear shifting buttons to the push mode?
umtiti 16.10.2020 klo 10.57 
reverse is broken
Facelesswaffel 2.9.2020 klo 10.47 
I'm using it on a boat but I can't seem to get reverse to work in automatic mode.