Página de la tienda
Stormworks: Build and Rescue
Todo Discusiones Capturas Artwork Retransmisiones Vídeos Workshop Noticias Guías Reseñas

Stormworks: Build and Rescue

Página de la tienda
Stormworks: Build and Rescue >  Workshop > Workshop de Karnivool
70 valoraciones
Career Helicopter
Descripción Discusiones0 Comentarios35 Notas sobre cambios
   
Premiar
Favoritos
Favorito
Quitar
Vehicles: Vehicle, Air, Rescue, Exploration, Delivery, Wip, Technical, Creative, Fire, Advanced
Etiquetas: v1.15.2
Tamaño
Publicado el
Actualizado el
638.418 KB
19 JUN a las 20:54
16 AGO a las 20:35
8 notas sobre cambios ( ver )
Creado por
Karnivool
en línea
Ver las 132 colecciones (algunas podrían estar ocultas)
12,170 Visitantes únicos
19,227 Suscriptores actuales
117 Favoritos actuales

Suscríbete para descargar
Career Helicopter

Descripción
DESCRIPTION

The C Helicopter is a career helicopter designed and built in my recent career play through. Designed to be cheap and efficient the C Heli features Autoland and Autopilot as well as Zizos map/radar and an easy to use transponder locator
INSTRUCTIONS
-ENGINE IGNITION KEY -W/S for Pitch -A/D for Yaw -LEFT/RIGHT for Roll -UP/DOWN for Collective -1 to activate the helmet hud ZIZO'S Map screen 1,2,3 top left buttons change between the different map modes R turns on/off the radar TL turns on/off the transponder locator when a transponder is found a circle is drawn on the map indicating range to target and possible search area. Autopilot/Autoland enter a waypoint into the keypad located above the co pilots seat select either the autopilot or autoland button Fuel and Electrical anchors are located under the helicopter Harness use the "master" harness to go up/down or use the instrument panel located above the rear door to safely exit it is recommended to grab onto a handle first before leaving the harness.
SPECIFICATIONS
Cost: $22,275 Mass: 1,216 Length:10.25M Width: 3.75M Height: 4.25M Fuel: 350L Top speed: 151 KM/H Seats: 6 Engine: KA 16 cylinder Diesel
CREDITS
Zizo map and radar Transponder Locator Industrial helmet hud Ze modular engine controller ZE base gyro Horizon
UPDATES
-fixed nav lights -fixed hmd physics sensor -added weight to the rotor assembly - added the SRS transponder/reciever (lost the radar sorry no more room) should show up on the Kwazii's transponder now
35 comentarios
< >
kknutsen456 30 AGO a las 6:21 
Really awsome helicopter! can even fly with one blade XD
Karnivool  [autor] 16 AGO a las 20:38 
I just updated the workshop. Radio gets disabled when you toggle autopilot. There is also a hotkey on the seat to swap yaw/roll
Fogest 16 AGO a las 16:06 
I just picture the use case of the auto pilot being to get you out to your rescue (or whatever), and then the autoland to get you back. So I think it would make sense for it to cut the signal when auto pilot is being used so that you don't have to worry about changing the channel to something else and changing it back when wanting to return.

Not sure if there is a different use case you're picturing where having to change the channel to use the auto pilot would be more appropriate? I personally thought the auto pilot wasn't working, because I didn't realise I'd need to change the channel on the auto land to have it work.
Karnivool  [autor] 15 AGO a las 22:56 
I could add a simple bit of logic that cuts the radio signal if autopilot is enabled.
Karnivool  [autor] 15 AGO a las 20:49 
the autopilot waypoint gets overridden if there's a radio signal detrected.
Fogest 15 AGO a las 20:45 
So it seems that if my autoland channel is set at 0, when I activate auto pilot (but not auto land) it will navigate to the boat even if I have waypoints set. I have to change the channel to something else to get it to correctly autopilot to the waypoints. Maybe I am mistaken, but shouldn't the auto pilot go to the waypoints even if the channel is 0 (matching the boat)? And then autoland should be the part that is dependent on the channel?
Karnivool  [autor] 13 AGO a las 14:22 
Yeah I might. The logic is there in the gyro. Just have to hook up a button
timobecher 13 AGO a las 10:08 
I wonder, could you make it so one can switch the input for yaw and roll? I am more used to A/D being roll so if people like me could switch that with a button that would keep things simple and easy no matter what you are used to
Karnivool  [autor] 11 AGO a las 19:22 
ended up swapping the autopilot system to the SRS system can do multi waypoint and also shows up on the transponder map
Karnivool  [autor] 11 AGO a las 18:06 
nope should work. There's no line on the map with this one i just tested it and it works for me.
Input waypoint on the keypad click submit then press the autopilot button. Or autoland if you want to land there