Was going very well until I got held at a red signal outside York at about 19:41, the arrived at York at 19:43, two minutes before the ETA, but for some reason my arrival was recorded as 19:47 and I failed the scenario! I didn't save or pause during the scenario. Shame, was enjoying it until then.

If the only thing you altered was the enhanced 91 version I guesss that must be the issue.

I suggest making a copy of the scenario, delete the 142 causing the issue in the copy. Then run the copy as see what happens.

OK here's something weird. I'm re-running part 1 but I've replaced the Class 91 with the AP enhanced version (which is awesome). I don't think this created the issue, but when I got into Newcastle and waited for the red prior to the station, the 142 leaving Newcastle "leaves the path" and the scenario ends in error. I have tried saving and restarting from a number of points leading up to the signal, but I get the error every time. This did not happen the first time I ran the scenario. Odd.

lol....nope, well not yet anyway.

Love it! I've been waiting to get all the route segments to try this. It was worth the wait. On to part 3. Any chance you'll be making a northbound 4 part version?

stulomax

Message me

Hi Graham, really frustrated, I dont know if you can help, but, evertime I try to load this senario from Pt 1 to Pt 4 it keps coming with an error, cant load Mk4 fod and so on, I downloaded and installed all the reskins required, even installed AP Class 91 Enhancement Pack, still wont run, tried using F2 but the Loco Set is not there. Have you any idea what i have done wrong? gone through the RSC file for the 91 Addon and the geo files are there for what i have installed.

Hi Graham, No I did not save but I think I was a little late arriving at the red signal.

Did you save again? Should have stopped at signal at 19:41, were you on time there?

Part 2 Graham. Got as far as the last stop before York, and held there at a red until approx 1948 - 3mins late, so arrival at York at 1949, then got a Bad Luck, Failed to complete the scenario. Where did I go wrong this time?. Thank you for another great scenario.

It worked Graham, I ran the scenario again, this time as you suggested without saving, and completed a fabulous part 1. I am now looking forward to part 2. Thank you so very much for all your help and patience.

yes but i fixed now by using RWtools

So when you make a scenario with it can you see it?

same for part 1 as well no class 91 flying scotsman to be seen wich weird because its still can be seen when you select it when making a scenario have not tried parts 2 and 4 yet

Part 3 is York-Peterborough. I assume you have tried parts 1/2?

i meant part 3

hi for some reason on part 2 the train that i'm supposed to be driving is nowhere to be seen i have downloaded all geo files and put them into the game and checked to see if they worked which they have so this is wierd

yes, more than likely

Graham, yes I saved approx 3 miles from Newcastle. Is that where I went wrong?.

Did you save?

Hi again Graham, Part 1 was fantastic, everything went well until I was stopped at a red (Last signal before the Newcastle stop) 1M72 was in Platform 3. Then got a game over Al 2N46 1743 Hexham - Nunthorpe had left the path.

I fixed a problem I found with GEML Class 90 Greater Anglia Branding on UKTrainsim and BHReskins VTEC HST to stop the Anglia Branding applying to the BHReskins VTEC HST here on facebook https://www.facebook.com/groups/430356467097416/permalink/819856378147421/

Hi Graham, I am so sorry to be a pain. The DPS install info says install with Package Manager - Have done. Go to Assete Oovee and click the Installme. Under assets/Oovee the line reads - InstallMeMurcoTDA 08/05/16 Windows Batch File. If I click on it a black box flashes up and normally the batch file disappears, this one doesn't. In my Oovee folder thge TEA wagons are present but the red one only shows Red 1 and Red 2, I think there should be one just Red and that is no doubt the one that is flagging up as Can't load rail vehicle TEA VTG Red Empty. I have accepted your friend request. (Bet you don't want many friends as thick as me)

click on bat file twice slowly so you get the curser flashing within the file name. then click to the end then backspace 3 times to remove bat. then type cmd. hit return and click yes when prompted. then double click on the file now it has cmd on the end and it will run, failing that accept my friend request and i'll talk you through it

Forgive me for asking, but how would I go about changing the bat file to cmd. I am a bit thick.

Ok :D

Yes, I know. My mistake I thought the AXC came with the Riviera line, not a reskin

RW Tools says
RSC\RivieraLine\RailVehicles\Diesel\HST\AXC\Class43\class43_fgw.bin
RSC\RivieraLine\RailVehicles\Diesel\HST\AXC\Class43\class43_fgw_nd.bin
RSC\RivieraLine\RailVehicles\Diesel\HST\AXC\Mk3TF\mk3tcc_fgw.bin
RSC\RivieraLine\RailVehicles\Diesel\HST\AXC\Mk3TF\mk3tf_fgw.bin
RSC\RivieraLine\RailVehicles\Diesel\HST\AXC\Mk3TS\mk3tgs_fgw_A.bin
RSC\RivieraLine\RailVehicles\Diesel\HST\AXC\Mk3TS\mk3tso_fgw_B.bin

change the .bat to .cmd

I have the original Oovee TEA & Class 70, and get the can't load rail vehicle TEA VTG Red Empty when I try to run part 1. I have the TDA Murco from DPS but when I install the rwp and go to the Oovee folder the Installme Batch file will not install.

Riviera line will stop it as that is what was used.

OK but it stops the load error

That is correct, but you do not need the CC HST repaint.

Part 1 needs TDA 'Murco Petroleum' Repaint (3 Variations) from DPS rf72reskins