Subscribe to download
F/V Branntelle

*UPLOADED FOR PERSONAL BACKUP FOR TIME BEING*

This is a scallop dragger based out of Digby, NS, Canada.

Cruising speed of 9 Knots.
The hoppers are set up to be compatible with Zizo's trawler mod.

Next update will have the interior finished, the bilge system operating appropriately, and breaker panels, and gen-set powered assets all set up.
Currently sorting out the bilge issue's.

Operating Vessel: vessel spawns with engine running, simply turn on the systems with the flip switch beside the seat.

Fishing Gear: if when the vessel spawns the gear ends up on deck, or not over the side properly, then you can lift it up with the "dump rope" (the rope connector dangling off the dumping pole), and set the boom out and lower the gear to set it back over the side. some times it is finicky and you need to set the boat to cut hard to stbd to swing the gear out.

To enable the multiple winch controls and other "hydraulic" controls you must enable the PTO clutch which is the switch above the winch control panel.
Before shooting the gear away, make sure the gallos switch is on (to set the gallos out over the side), and that the dump pole is out over the side and that the hoppers are at the top of the table. To shoot the gear away flip the "table pins" switch to release the gear. sometimes the drag bar may get caught on the table. if it does, you can lift the table and then "grab" the electrical connector closest to you on the drag bar and it should slide out over the side.
You must reverse the main winch to allow the gear to run out of course.

When hauling the gear back, when it gets to the gallos there is an empty rope connector. connect the boom winch cable to that, and start lifting it with the boom, while also letting out the main winch. Then grab the rope by the third man winch and connect that to the empty rope connector on the drag bar and then to the third man winch. once the hoppers are about halfway above the table you can start to pull in the third man, while lowering the boom winch. try to get the electrical connectors on the gear to line up with the ones on the table and it should snap into place. remove fish by hand, and use the sliding hatch between the table and the fish hold access to put them into the hold.

*Video and pictures of operating procedures coming soon*

COMPATIBLE WITH:




MC CREDITS
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=1566157334 1x1 letters
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=2406528070 2x1 letters
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=2090272370 stove
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=2286139600 compact nav display
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=2322222756 environmental screen
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=2830904924 Map
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=3019702522 analog chart
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=2787024185 Sea Depth Graph
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=2280998825 Marine Lighting Panel
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=2387970060 Spectrum VHF
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=2800237177 Radar
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=2365575314 Autopilot
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=2824744715 Heading Hold
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=2802915346 Main engine, ECU and Transmission controllers
https://gtm.steamproxy.vip/workshop/filedetails/?id=3025094276 Rudder indicator, Heading & R.O.T (many other useful marine controllers)
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=2384103710 Generator and Controller (Pre UI update MC installed)