Subscribe to download
(BROKEN) HELEN K. Oil Product Tanker

Notice!
after some update the creation does not fulfill its main function - separation specific fluid and transfer out it to the manifold/shore.

Helen K. - tanker with a capacity of 100,000 liters and capable of transporting various types of oil at the same time. The rate of discharging/loading was increased as much as allowed by the game mechanics For instance, loading with 3 hoses are connected - 95 litres/sec, discharging - 87 l/sec. The cargo system management has been simplified (see manual below ) Ship's heading control assistant has been added due to high demand. The ship has a modular engine with ability to boost. Lidar and map are combined in one display. You have an opportunity to drop anchors from navigation bridge and forecastle. Ship handling for mooring operation can be made using the remote control unit. I tried to optimise the ship so that it wouldn't have a lags and low TPS/FPS and now I have in my computer 60 FPS and 62 logic fps, 60 TPS with this creation loaded.
I hope you will like my creation, I tried to make it simple and optimized. Enjoy!




Type of ship: Oil product tanker
Total cargo capaсity: 100 000 l
Fuel capacity: 30 221 l
Fuel consumption: 1.27 L/sec on full throttle, 1.5-1.7 - full throttle+full boost
Max speed: 18 knots(max boost - 23 knots)
Max rates: loading with 3 hoses are connected-95 litres/sec,discharging - 87 l/sec.
Automatically diesel generator (manual starting and charging battery can be made from Diesel generator room)
Searchlight switching assistant(handling any one of three searchlights without leaving the helm)
Lidar by Geekness
Heading monitor (remade Heading Display (analog) v2.3 by PenguinO )
Map (remade Intercative Lua Map by markers622 )
Heading assistant (remade Rudder Controller by sengir_vampire )
Fuel Consumption by IamPhilipp
Maneuvering mode (throttle control on W/S axis and remote control unit available for using after switching on the button) Remote Controller Settings by Struner
Purging and drying systems
Thruster (left/right axis)
Anchors (control from navigation bridge and forecastle)



operating manual


Go to navigation bridge, take the helm. Push the key-button for starting the engine. The throttle lever to control main engine is located at left side. The boost level changer located at same panel. The engine is controlled by a throttle lever. Use A/D axis on the helm to turn the ship left/right. Button 1 - reverse gear (NOTICE! Take lower down to 0 the throttle lever before switching the reverse gear) Left/right axis on the helm steer the thruster. "Hold current heading" button (located near key button) activate Heading assistant that holds current ship's course automatically.

Searchlight managing panel located on the right side panel. Selected searchlight is shown on the radial segment, "switch on selected searchlight" button switches on currently searchlight. Use 2,3,4,5 buttons on the helm for changing the searchlight position (up/down, left/right).The button "Select searchlight to control" selects next searchlight to control it (On/off, changing position)

Maneuvering mode button activates engine throttle control with W/S axis on the helm and allows to use the remote control unit for handling the ship.




Cargo system panel

The numbers on the cargo operation panel represent the numbers of manifolds on the deck. To begin loading operation you must connect hose/hoses to cargo manifold/s on the deck (fluid hose anchors with numbers 1 2 3 4 5 6). Remember the manifold number to which you connected the hose and get to the cargo operation room. Switch on the "loading operation" button under the connected manifold number. Fluid pumping into cargo tank must start. Switch off the button for stop operation

Discharging operation. Connect a hose/hoses to the cargo manifold/s on the deck (fluid hose anchors with numbers 1 2 3 4 5 6). Remember the manifold number to which you connected the hose and get to the cargo operation room. Push the button with type of fluid which you need to discharge and switch the flip-button "discharging operation" on. Separation camera will be filling and discharging to shore. As the concentration of the selected liquid in the tank decreases, the unloading rate will decrease.This applies if you have several types of fluids in the tank.
If you suspect that one of manifold's pipe is clogged, use purging system to clean. Type the number of suspected manifold on the keyboard and hold down "start purging" button for a few seconds.





Ballast panel

The ballast system has 4 ballast tanks. Scheme with tank locations and their numbers located above the ballast control panel. Type on the keyboard the percentage of filling the tank. "Start Ballast pumps" button will start the filling pumps and "Stop Ballast pumps" button will stop the pumps.




RECOMMENDATION
Fill the ballast tanks when the ship is being used without cargo .The minimum level is 10-15%