상점 페이지
Stormworks: Build and Rescue
전체 토론 스크린샷 아트워크 방송 동영상 창작마당 뉴스 가이드 평가

Stormworks: Build and Rescue

상점 페이지
Stormworks: Build and Rescue >  창작마당 > MrNJersey 님의 창작마당
140 평점
NJ Modular Engine ECU V5 (Throttle Lever + Key Switch)
설명 토론0 댓글149 업데이트 노트
2
   
어워드
즐겨찾기
즐겨찾기됨
즐겨찾기 해제
Microcontrollers: Calculation, Cockpit, Modular, Microcontroller
태그: v1.1.17
파일 크기
게시일
업데이트일
466.483 KB
2021년 3월 5일 오전 2시 06분
2021년 3월 29일 오전 8시 28분
업데이트 노트 4개 (보기)
제작자
MrNJersey
오프라인
모음집 308개 모두 보기 (숨긴 상태 몇 개 있을 수 있습니다)
23,129 순 방문자 수
15,275 현재 구독자 수
201 현재 즐겨찾기 수

다운로드 위해 구독하기
NJ Modular Engine ECU V5 (Throttle Lever + Key Switch)

설명
NJ Modular Engine ECU V5 (Throttle Lever + Key Switch)

This controller can be used on all types of modular engines you want to control, From small car engines with air pumps to large marine engines with air exchangers etc. This system will read the composite data from your engine and adjust the Air/Fuel depending on what it needs to reach the desired AFR value. Meaning that you can any type of setup and any size too.

FEATURES

Fully auto system that manages the Air Fuel Ratio.
Customizable AFR Value "Recommended 14:4" (Can be changed on Controller)
Idle RPS (Can be changed on Controller)
Data Node to Read Engine Info (Channels Listed Below)
Can be connected to NJ Auto Transmission Controller Gear Switching
Compact Design - 4x3

INTENDED SETUP

ENGINE ----> MODULAR ENGINE CLUTCH ----> ELECTRIC ENGINE ----> GEARBOXES ----> CLUTCH(OPTIONAL) ----> PROP/ROTOR/WHEELS

USE A THROTTLE AND KEY SWITCH TO CONTROL THE ECU

READABLE DATA CHANNELS - Can be Connected to Composite Panel
01 - Engine On/Off
10 - RPS
11 - Gear (If using NJ Transmission)
12 - Reverse Gear Active (If using NJ Transmission)
13 - AFR
14 - Speed (m/s)
15- Temp


As always please comment and report any bugs you find.

I will keep this creation updated where possible and be sure to keep a lookout for my upcoming creations!!!!!!!!

Please do not re-upload or share without my permission, including custom versions!!!!

And lastly, have fun.

Don't forget to click the "Follow" button for future updates!!!!!!!!!!!!!
댓글 149개
< >
frog with da gun 2025년 6월 30일 오후 2시 05분 
for some reason it keeps shuting off and turning on the starters when im using this one and the 6.3
zdauzat14 2025년 4월 14일 오후 4시 33분 
i am subed on youtub
Sleeper____ 2025년 2월 22일 오후 5시 53분 
Forgot to say, the exhaust values are above 1 but the manifold is 0L/s
Sleeper____ 2025년 2월 22일 오후 5시 52분 
Also my engine doesn't work, it says it's outputting more air and fuel that is actually inside it, and listed volumes of both are below 0.01. Stays at around 1.1 RPS regardless of the desired idle. Really wish this engine adjusted to the desired idle/throttle rather than the AFR.
Sleeper____ 2025년 2월 22일 오후 5시 47분 
You can't actually set the AFR to the recommended 14:4 (3.5:1), at least from what I understand. Unless you meant 14.4.
Indiana Jones 2024년 8월 3일 오전 10시 45분 
Hello, could i use this on my vehicle? I will give credit ofc.
bartakrisztian85 2024년 7월 30일 오전 5시 52분 
Engine Rps always skyrockets and then falls stalling the engine
Nerofu 2023년 11월 17일 오전 8시 09분 
Help! My engines are ceeping overheating. An electric radiator have to be enough to run a small 4 cylinder engine
Bobmiller764 2023년 9월 17일 오전 11시 24분 
also the seat ecu seems to work fine, its just this ecu that i cant get to work
Bobmiller764 2023년 9월 17일 오전 11시 23분 
i cant seem to keep the engine running, it'll run for 5 seconds then kill itself slowly. the ecu constantly says to much fuel no matter what i try. anyone got any idea's?