商店页面
Medieval Engineers
全部 讨论 截图 艺术作品 实况直播 视频 创意工坊 新闻 指南 评测

Medieval Engineers

商店页面
Medieval Engineers >  创意工坊 > peaceman 的创意工坊
180 个评价
Balloons
描述 讨论0 留言211 改动说明
   
奖励
收藏
已收藏
取消收藏
Type: Mod
Mod category: block, script, modpack
Version: 0.7
文件大小
发表于
更新日期
12.668 MB
2017 年 11 月 7 日 下午 3:23
6 月 23 日 下午 3:07
130 项改动说明 （ 查看 ）
必需物品
这件物品需要以下所有其它物品
创建者
peaceman
离线
查看所有 369 个合集（也许有些被隐藏了）
14,998 不重复访客数
10,732 当前订阅者
322 当前收藏人数

订阅以下载
Balloons

描述
This mod adds Balloons to Medieval Engineers

Place some fuel inside, light it and use the paddle to increase its lift. Each balloon has a maximum lift of ±1500kg at ground level, the higher you go the less lift it will have. Don't worry, even with no load your balloons will never reach space !

Make sure your balloon is attached by a rope or it will fly off until it runs out of fuel. Even after it runs out of fuel it will slowly decent again.

When designing your flying stuff make sure you can reach your balloon to change the lift or refueling. If not you can always use chests to change your altitude.
Creating and flying balloons will be a learning experience, especially in survival. (creating flying castles with catapults IS possible)

This mod also adds a propeller to turn and move your craft while in the air. Attach it to a catchblock and make it spin ! the faster it spins the more thrust it provides.

Check out the player harness mod: http://gtm.steamproxy.vip/sharedfiles/filedetails/?id=1199350061
It allows you to attach yourself "safely" to any grid or even launch yourself.

If you like my mods, consider sending me some love -> [www.paypal.com]
211 条留言
< >
peaceman  [作者] 2022 年 9 月 12 日 上午 9:07 
Contact me on discord, I will send you the blender file of the model
SicH 2022 年 9 月 11 日 上午 2:24 
how about turbine props with variable diameter? To don't have square "engines" with 4 subgrids for airliners. But to have one 9.5-10 small blocks prop, placed inside the round "engine". Or to be able to place smaller "engines" for regional jets / fighter jets / etc. Could do it by myself, but I don't have any opportunity to scale the original model. The only way to scale it afaik is scaling the model before processing into .mwm
gabgab01 2022 年 7 月 21 日 上午 11:52 
i can understand that it's intended, but in reality it's kind of a balancing issue.
because if you use a large balloon, you end up having to add a lot of weight / mass in order to even be able to land it, which in turn increases the total mass, and you need bigger / more steam engines to even propel it, which in turn makes it even heavier and slower again, and so on.

and at those sizes it starts afflicting the sim speed on servers.

nevertheless, it's still an awesome mod!
peaceman  [作者] 2022 年 7 月 21 日 上午 9:12 
You mean with the heat panel closed? This is intended. Not all heat is blocked so the balloon still has some lift. I think its like 25% of max lift
gabgab01 2022 年 7 月 3 日 上午 10:22 
the balloons never have 0 lift when they're turned on.
i always need a crate full of ore to even be able to land with the big balloon. otherwise i'd be stuck at a height of 450 metres on minimal lift, which makes these even more expensive in survival :D
Terradus 2022 年 6 月 19 日 上午 5:54 
@peacema
Why for this mod need steam engines mod ? Can you please create "balons" mod without dependencies with "steam engine" and "Pulleys" mods ?
peaceman  [作者] 2021 年 7 月 13 日 上午 11:28 
Drafting table
Hoplite 2021 年 7 月 13 日 上午 8:40 
so where i can get blank scrolls
Hektor Riven 2020 年 10 月 30 日 上午 11:33 
The balloon "breaks" without noise or animation: just disappears with the rope and its eye plate.
I've considered to place the balloon directly on the grid, however I was never able to do it but once, and just for a small grid attached to a large grid standing on the ground. Adding the balloon to a free grid seemed to be impossible for me, but I'll keep trying.
Thanks again for your support!
peaceman  [作者] 2020 年 10 月 30 日 上午 9:29 
I see, it breaks the balloon when the rope breaks? Or does the balloon just fly off into near space? :D
I suggest not using ropes. Just attach the balloon directly to your grid. Place it above center of mass then all should be stable