Butiksside
Stormworks: Build and Rescue
Alt Diskussioner Skærmbilleder Illustrationer Broadcasts Videoer Værksted Nyheder Guider Anmeldelser

Stormworks: Build and Rescue

Butiksside
Stormworks: Build and Rescue >  Værksted > Tajins værksted > Logic: Altitude hold example (PID based)
Logic: Altitude hold example (PID based)
Beskrivelse Diskussioner0 Kommentarer14 Ændringsbemærkninger
14 kommentarer
< >
syrenevice 16. maj 2019 kl. 23:46 
Nice and simple works.
It takes easy to understand.
Thanks!!
Sgt. Max Cockburn 19. sep. 2018 kl. 4:25 
OK, I think I understand that.

Not sure what the "collective" represents, as I'm still unsure what several other concepts and modules represent. That makes it hard to figure stuff out.

I copied your system on my chopper and it works, just not sure why lol.

Thanks for your time.
Sgt. Max Cockburn 18. sep. 2018 kl. 9:33 
And what does that accomplish? What's the reasoning behind "combining" the outputs? I'm completely stuck lol.

I more or less tried to replicate this just now, but it still doesn't do anything for me. I just have up/down fed into Add B, otherwise it's the same - just without the clam.

Tajin  [ophavsmand] 18. sep. 2018 kl. 9:00 
the "add" simply combines the output from the pid with the output from the pilot seat,
Sgt. Max Cockburn 18. sep. 2018 kl. 8:05 
What is the use of the Add logic component? I think it's why I can't get my system to work.
SamuelPepys 30. juli 2018 kl. 17:41 
Ah, ok. I got it, I just needed to adjust the PID values and the value being sent to the collective. I just put the differential up to super high levels (7 I think), the proportional quite low and then adjusted the clamp gate numbers down to make the helicopter not free fall once I used the keypad to enter a lower altitude. Everything works awesomely now!
SamuelPepys 30. juli 2018 kl. 15:13 
Hi! The system makes the helicopter spin around violently and uncontrollably. I am using a keypad to control altitude, and I think it has to do with the speed that it tries to acchieve the altitude. Is there a way to reduce the speed of which it tries to compensate?
Tajin  [ophavsmand] 30. juli 2018 kl. 10:05 
Logic in this one stores the current altitude in a memory gate. So just replace that with a keypad to enter your desired altitude.
MW-777 26. juli 2018 kl. 7:12 
is there a way of making it so i type an altitude i want and it takes me to it and holds that altituse?
if you know what i mean :)
PoyoSkytower 23. juli 2018 kl. 5:02 
ah i got you.
thank you :)
Tajin  [ophavsmand] 23. juli 2018 kl. 4:50 
You will have to adjust the settings on the PID to suit your helicopter as the one in the example is very small and light. Yours will likely have different requirements.
PoyoSkytower 23. juli 2018 kl. 4:42 
i mean i copied your system onto my helicopter but it does not seem to be working :c
Tajin  [ophavsmand] 23. juli 2018 kl. 4:40 
doesn't do that for me.

- Get in
- Turn engine on
- Enable hover
- Press W to get to desired alt
- Activate allt hold

Should be fairly simple.
PoyoSkytower 23. juli 2018 kl. 4:34 
Im not sure what im doing wrong here but using this example the helicopter just shoots right up on full throttle