Testing of the Mk2 Penguin after i made the upgrade to Mk3

the unused parts if you are making the Mk3 penguin are

T4 rudder = 2
T8 rudder = 1

Requirements:

RP = 5118236 (possibly 1 RP off)
pFlops = 1492 (with cosmetics)
Cube/inner = 140
Prism = 100
Tetra = 8
Pilot seat = 1
T9 radar = 1
T9 radar jammer = 1
T7 radar jammer = 1
T10 walker legs = 6
T10 thrusters = 6
T8 rudder = 1
T4 rudder = 2
T10 rail cannon = 7
T6 electroplate = 2
T7 electroplate = 4
T9 electroplate = 4

Recommendations:

Cosmetic spike = 6
Flag = 2
L2 vapour trail = 2

Build Video (if you dont want to use a video, keep going for a picture guide)

Start off with a rounded T shape with a downward prism at the front.








Now make a 3x5 rectangle with one cube at the back as the bottom layer.








Finally round some edges off and remove the two blocks that make the hole for the cockpit.

Start with 2 cubes under the hole for the pilot seat as the base, at the front and back add 2 downward facing prisms, also do this for the sides of the back prism that you just added.






Attached to the back prism finish this shape as one of the 6 connection points.








Now complete this shape on the side prisms.









And now this shape on the front prism.

First build 1 back from the rear connection point and the build 3 out.








now build this shape with a hole to marginally reduce weight.








Now build this structure to hold the radar.

To begin with, build one prism on each side for the start of the connection point.








Now place two prisms on each side facing out then down.








Finally add one more prism to each side to connect with the hull.

Build towards the middle connection points and when you reach this spot build out 3 cubes, not 2 like the picture shows.







Now build forward with a 3x5 rectangle like shown in the picture.








Connect two rectangles with a 3x3 between them.

Now build forward 3 lines of cubes, first a 7x1, then a 5x1 and finally a 3x1 with a downward facing prism in the center for asthetic purposes.







Now add these 2 prisms and tetras on each side, also for asthetics.

First add these 2 tetras on each side for the connection to the hull.








Now add this a prism to the centermost tetra facing forward.








now add this shape to hold most of the arm and a steering thruster.








Continue the shape by adding these prisms.









Now finish the arm with these final prisms

First and finally build this shape like this.

Start with a prism and tetra on each side like this.









Add 3 prisms on each side like this.









Repeat previous step.









Repeat previous step.









Finally finish the arm with these 3 prisms on each side.

Add the pilot seat in the cockpit.









Place Radar on rear pillar.









Place 2 T9 electroplates like this around the top of the cockpit.








Place 2 T7 electroplates like this at the front of the bot.








Place 2 more T7 electroplates on the bottom of the bot.








Place 2 T9 elactroplates on the bottom, same as the ones on the top.









Place two cubes and a T9 radar jammer on the bottom of the bot like this.

Place T7 radar jammer behind the T9 jammer like this.








Place two T6 electroplates at the back of the bot like so.

Place 1 T8 and 2 T4 rudders like so at the back of the bot.

Place 2 L2 Vapour Trails at the back of the bot like so.








Place 6 cosmetic spikes at front like shown in picture.








Place flags like so at the back of the bot.









Place T10 thrusters like so in specific spots.









Place legs like so on the sides of the bot.

Place Rails like so on arms and cockpit.

- This is a flimsy bot, do not run in unless you can get away in 10 seconds max
- Please DO NOT critisize it negatively.
- I will take suggestions but not orders
- This bot is plausable in T9 but not quite as heavy, fast, tanky or powerful (obviously)
- Thank you for taking your time to read this

ADMITTED - this was a complete fluke that this worked, Mk1 was ok but i added the steering thrusters and upped it even more + i added some other stuff

YOUTUBE LINK = https://www.youtube.com/channel/UCCyjLkzOEn8Vu4unBA1efHg

Requirements

pFlops = 1498
Prism = 2
T10 Rudder = 1
T10 Thruster = 2

Salvages

T4 rudder = 2
T8 rudder = 1

Start at the back of the bot.









Remove the 3 rudders, the 2 prisms and the 2 vapor trails.








Add the thrusters in like so.









Add in T10 rudder between the thrusters.









Use the salvaged prisms and the 2 new ones to build this structure.








Place L2 vapour trails like shown in the picture

- Mk4 is currently being developed
- do not complain if i wasted your RP on unused rudders as i mentioned it at the start
- Thank you even more if you made the Mk3