Butikssida
Stormworks: Build and Rescue
Alla Diskussioner Skärmbilder Konst Sändningar Filmer Workshop Nyheter Guider Recensioner

Stormworks: Build and Rescue

Butikssida
Stormworks: Build and Rescue >  Workshop > Lazy Cats workshop
Otillräckligt med betyg
LC Configurable 4 Gear Automatic Transmission V0.1
Beskrivning Diskussioner0 Kommentarer12 Ändringar
   
Utmärkelse
Favorit
Favoritmarkerad
Avfavoritmarkerad
Vehicles: Land, Mechanical
Microcontrollers: Composite, Modular, Microcontroller
Taggar: v1.7.4
Filstorlek
Lades upp
Uppdaterades
42.183 KB
29 apr, 2023 @ 13:20
29 apr, 2023 @ 13:22
2 ändringsnotiser ( visa )
Skapat av
Lazy Cat
Spelar
Factorio
Se alla 34 samlingar
1,324 Unika besökare
668 Nuvarande abonnemang
8 Nuvarande favoriter

Abonnera för att ladda ner
LC Configurable 4 Gear Automatic Transmission V0.1

Beskrivning
Highly configurable automatic transmission that is made to work with my ECU out of the box.


Default button mapping is as follows:

1: Gear Up
2: Gear Down

Up/Down axis: Gear Up/Down

Button mapping can be adjusted as desired.

Buttons will need to be set to push, and any axis that is to be used will have to be set to 100% sensitivity.

Output channels:
1-7 (on/off): seven segment display(on on/off mode)
1 (number): gear selector position
2 (number): automatic gear position
12 kommentarer
< >
LynxarA 2 sep @ 8:19 
(Update) Problem was fixed. In the configuration Automatic Gearbox was not needed with the current settings I had, deleting it solved the issue
Lazy Cat  [skapare] 1 sep @ 8:39 
i might have accidentally cleared the friend request as i get a lot of spam, can try again? that is the correct username
LynxarA 1 sep @ 6:19 
Yes, I use gear Shift Type: Buttons and both buttons 1 and 2 are push, tried with Axis (sensitivity 100%) and it doesn't work the same way. I've sent a friend request in Discord if you are lazycat42, if not, can you send your current one so I can send screenshots?
Lazy Cat  [skapare] 1 sep @ 6:07 
if you can contact on steam or discord maybe i will be able to help, i doubt it has much to do with the controller, is your seat sensitivity set to 100% on gear axis? is gear up/down buttons set to push?
LynxarA 1 sep @ 5:08 
And yeah, I tested your engine with another controller and it worked, when I removed previous controller and installed your automatic gearbox and ECU, then it started behaving like that
LynxarA 1 sep @ 5:06 
Same issue as Soveless, only reverse works, but I can not upload the vehicle for testing, because it says "cannot upload modded vehicles" for some reason (no modded parts were used in the build).
I can send you screenshots of configuration of this build in Steam dms tho
Lazy Cat  [skapare] 28 dec, 2023 @ 17:29 
the ecu is this:
https://gtm.steamproxy.vip/sharedfiles/filedetails/?id=2803654162
notyap989 28 dec, 2023 @ 13:33 
whats the ecu
Lazy Cat  [skapare] 27 okt, 2023 @ 4:26 
Hey, can you send the vehicle over in some way? I think it'd be easier if i were to take a look myself in-game, it's bit hard to communicate through steam chat.
Soveless 26 okt, 2023 @ 7:11 
So, Gearing up seems to only cause the vehicle to go into reverse. None of the gears actually cycle through, gear 1 is 1:1,1:3, same for 2 and 3, the reverse gear is 1:3,1:-1 using one of your flat v8's and your ECU set to Automatic. any help would be nice