Mağaza Sayfası
Stormworks: Build and Rescue
Tümü Tartışmalar Ekran Görüntüleri Çizimler Yayınlar Videolar Atölye Haberler Rehberler İncelemeler

Stormworks: Build and Rescue

Mağaza Sayfası
Stormworks: Build and Rescue >  Atölye > Craig P Kullanıcısının Atölyesi
Yeterli oy yok
Radar Interpreter
Açıklama Tartışmalar0 Yorumlar18 Değişiklik Notları
   
Ödül
Favorilere Ekle
Favorilere Eklendi
Favorilerden Çıkar
Microcontrollers: Calculation, Navigation, Microcontroller
Etiketler: v1.3.15
Dosya Boyutu
Gönderilme
Güncellenme
32.226 KB
22 Kas 2021 @ 21:49
6 Ara 2021 @ 11:32
4 Değişiklik Notu ( görüntüle )
Oluşturan
Craig P
Çevrimdışı
13 koleksiyona göz atın (bazıları gizli olabilir)
1,100 Tekil Ziyaretçi
415 Mevcut Abone
4 Mevcut Favoriler

İndirmek için abone ol
Radar Interpreter

Açıklama
Couldn't find a simple, accurate, up-to-date radar display, so here it is. Doesn't require any kind of gymnastics - just feed it a signal and it'll put it on a screen.

Works with modern radar! No more weird jitters or obsolete gear.

It's pretty basic, but you can set ranges and when you tap the screen, it'll zoom to the new range smoothly. It's a lot less discombobulating than ones that snap.

You can use this however you like, I don't mind.
18 Yorum
< >
Redstone_Orange 20 Ağu 2022 @ 0:01 
oh ok, this is the only Radar i found that works with the modern ones. Please make it compatible with the 1x1 screen.
Craig P  [yaratıcı] 19 Ağu 2022 @ 10:28 
1x1 is a bit too small for me, sorry.
Redstone_Orange 19 Ağu 2022 @ 9:08 
Could you make it Compatible with the 1x1 screen?
Craig P  [yaratıcı] 7 Haz 2022 @ 14:20 
That would depend on the orientation of the radar and the screen.
.bishop 7 Haz 2022 @ 13:18 
hi, dont know if its a fault on my side or not, but i think the targets the radar found are upside down, i switched the minus signs (dx and dy) for the targets and the sweeper in onDraw around and then targets are shown were they really are for me. Nevertheless thanks for your awesome work.
ova578 4 Oca 2022 @ 16:05 
ok np
Craig P  [yaratıcı] 4 Oca 2022 @ 16:04 
Sorry, that's more than I can do in a comment.
ova578 4 Oca 2022 @ 14:18 
BTW i am really bad at LUA, so not always shure what it is im looking at haha
ova578 4 Oca 2022 @ 14:17 
basically You made a fancy animation when you change zoom. It looks good but I would like to always have the 3 inner circles positioned in the same place on the screen, recardless of the zoom
Craig P  [yaratıcı] 4 Oca 2022 @ 13:31 
Yes, but I'm unclear on exactly what you want. The code for that is all near the end of the script.