Strona w sklepie
Space Engineers
Wszystko Dyskusje Zrzuty ekranu Prace graficzne Transmisje Wideo Warsztat Aktualności Poradniki Recenzje

Space Engineers

Strona w sklepie
Space Engineers >  Warsztat > Warsztat użytkownika Spite
Zbyt mało ocen
ISL - Glis MK3-I 62 Tug
Opis Dyskusje0 Komentarze2 Lista zmian
   
Przyznaj nagrodę
Ulubione
Ulubione
Usuń z ulubionych
Type: Blueprint
Tagi: ship, small_grid
Rozmiar pliku
Zamieszczono
2.647 MB
23 września 2020 o 3:08
1 lista zmian ( zobacz )
Wymagane produkty
Ten produkt wymaga wszystkich następujących produktów
Twórca
Spite
Offline
Zobacz wszystkie kolekcje (324) stworzone przez Spite oraz innych użytkowników (niektóre mogą być ukryte)
1,508 Unikalni odwiedzający
3,938 Obecni subskrybenci
32 Obecne ulubione

Zasubskrybuj, aby pobrać
ISL - Glis MK3-I 62 Tug

W 3 kolekcjach stworzonych przez Spite
ISL - Small Grid Printable Ships (with Printer)
Przedmioty: 185
ISL Shipyard
Przedmioty: 218
ISL - Utility Ships
Przedmioty: 47
Opis
Purpose
A small ship with two front mounted landing gear, designed to manipulate objects, equipped with the PAM script for easy gravity aligning (lifting thrust is stronger than other directions) and returning to dock.

Features
Tools, Scripts & Weapons:
2 Front mounted landing gear
PAM script

Power:
2 Large Batteries
2 Small Batteries

Movement & Control:
1 Cockpit
1 Remote Control
1 Gyroscope
Small Atmospheric Thrusters
10 Small Atmospheric Thrusters
13 Small Ion Thrusters

Cargo Space
2 Connectors - not designed for carrying cargo

Miscellaneous:
2 Spotlights
Navigation Lights
Repair Projector

This ship has an empty mass of 16579 kgs, and can move with a full cargo at a maximum tilt of 90 degrees below horizon in atmosphere or 55 degrees in lunar gravity.

All Programmable blocks are turned off in this blueprint and all toolbars are the same from the cockpit and remote control.

All ships in this set have a rear mounted Merge block and can be printed using a welder wall with one (large grid) piston. However in this design the merge block will have to be ground down if docking via the rear connector, all blocks that require removal are painted bright red.

Toolbars
Toolbar 1
1. Thrusters All On
2. Thrusters All Off
3. Thrusters Braking On
4. Thrusters Braking Off
5. Lights On/Off
6. Connector Switch Lock
7.
8.
9.

Toolbar 2
1. Battery Discharge
2. Battery Recharge
3. Camera Front
4. Camera Underside
5. Camera Rear
6. Landing Gear Lock
7. Landing Gear Unlock
8. Landing Gear Autolock On/Off
9. Antenna Broadcast On/off

Toolbar 3
1. PB [PAM] "up"
2. PB [PAM] "down"
3. PB [PAM] "apply"
4.
5. PB [PAM] "Align"
6. PB [PAM] "homepos"
7.
8.
9.


Toolbar 6
1.
2.
3.
4.
5. Repair Projector On/Off
Komentarzy: 2
< >
Spite  [autor] 24 stycznia o 1:51 
Hi CD Clone,

To be honest, it was in part for ccmplete-ness (since there was the atmo + h2 version), but also so that it could use ion only, and not waste H2 for lighter loads, and then add the hydrogen thrust if some extra lift or braking power was needed, since Ion Thrusters are kind of weak.
CDClone 24 stycznia o 0:43 
im a little confused with the ion / atmo mix.... but otherwise really great design ;)