Trang cửa hàng
Space Engineers
Tất cả Thảo luận Ảnh chụp Tranh ảnh Phát sóng Video Workshop Tin tức Hướng dẫn Đánh giá

Space Engineers

Trang cửa hàng
Space Engineers >  Workshop > Workshop của Spite
26 lượt đánh giá
ISL - Myxini Tunnel Miner MK3-AO 880
Mô tả Thảo luận0 Bình luận3 Ghi chú thay đổi
   
Giải thưởng
Yêu thích
Đã yêu thích
Bỏ thích
Type: Blueprint
Nhãn: ship, small_grid, safe
Kích cỡ file
Đã đăng
Đã cập nhật
4.005 MB
17 Thg05, 2020 @ 10:35am
28 Thg04, 2021 @ 8:35am
5 ghi chú thay đổi ( xem )
DLC yêu cầu
Nội dung này yêu cầu cần có tất cả các DLC sau
Space Engineers - Decorative Pack
Nội dung yêu cầu
Nội dung này yêu cầu cần có các nội dung khác như sau
Tạo bởi
Spite
Rời mạng
Xem tất cả 391 bộ sưu tập tạo bởi Spite và những người khác (một số có thể bị ẩn)
2,183 Số khách thăm độc nhất
4,878 Người đăng ký hiện tại
44 Lượt yêu thích
Bạn cần DLC để sử dụng vật phẩm này.

Đăng ký để tải xuống
ISL - Myxini Tunnel Miner MK3-AO 880

Trong 3 bộ sưu tập tạo bởi Spite
ISL - Small Grid Printable Ships (with Printer)
185 vật phẩm
ISL Shipyard
218 vật phẩm
ISL - Small Grid Miners
60 vật phẩm
Mô tả
Purpose
A medium miner designed for tunneling horizontally or diagonally either manually or with the PAM autominer script.

The MK3 is available in all three thrust types, either as Agna (Basic Cockpit) or Myxini (industrial Cockpit) variants and features 4 connectors (allowing for varied docking options), a larger drill profile than the MK1 and MK2 Tunnel miners, and a stone ejection system.

The Hydrogen version can be used on moons but is not recommended for planets.

Features
Tools, Scripts & Weapons:
PAM Autominer script
Fancy Status Displays script
4 forward facing drills

Power:
7 Large Batteries

Movement & Control:
1 Cockpit
1 Remote Control
4 Gyroscopes
10 Large Atmospheric Thrusters
30 Small Atmospheric Thrusters

Cargo Space
4 Medium Cargo Containers
4 Connectors
4 Drills

Miscellaneous:
4 Cameras - Po, Sb, Rear, Underside
1 Ore Detector
1 Sensor (for use with PAM)
2 Spotlights
Repair Projector

This ship has an empty mass of 81341 kgs, and can move with a full cargo at a maximum tilt of 90 degrees below horizon, but cannot fly upside down.

All Programmable blocks are turned off in this blueprint and all toolbars are the same from the cockpit and remote control.

All ships in this set have a rear mounted Merge block and can be printed using a welder wall with one (large grid) piston.

Toolbars
Toolbar 1
1. Thrusters All On
2. Thrusters All Off
3. Thrusters Braking On
4. Thrusters Braking Off
5. Lights On/Off
6. Connectors Switch Lock
7. Camera Port
8. Camera Starboard
9.

Toolbar 2
1. Battery Discharge
2. Battery Recharge
3.
4. Camera Underside
5. Camera Rear
6. Drill Control
7. Drills On/Off
8. Ore Detector On/Off
9. Antenna Broadcast On/off

Toolbar 3
1. PB [PAM] "up"
2. PB [PAM] "down"
3. PB [PAM] "apply"
4. Ejector System On/Off
5. PB [PAM] "Align"
6. PB [PAM] "homepos"

Toolbar 6
1.
2.
3.
4.
5. Repair Projector On/Off
3 bình luận
< >
omni 22 Thg07, 2023 @ 9:11am 
so his problem might be caused by having thrusters on as when they are on they cause it to clang out or atleast that is what i have found when printing it
Spite  [tác giả] 9 Thg01, 2021 @ 8:21pm 
Thanks GuitarEC, glad you like the design.

As for your printing problem, the welder wall is definitely big enough.

are you printing layer by layer? This can be done using butting for increasing and decreasing minimum distance on the piston. This has been the only reliable way for me.

Or are you letting the piston retract all the way in one go? No matter how slowly, this usually leaves out some blocks, especially in the more complex designs
GuitarEC 9 Thg01, 2021 @ 7:48pm 
I love the design, but it was a real bear to print for some reason - lots of blocks that didn't print, and I had to follow behind and manually weld things - sometimes having to grind out surface armor to get to inner areas (gyros, projector, etc). FYI - my printer is a 5x3 grid, piston travel is only 0.15 m/s.