상점 페이지
Space Engineers
전체 토론 스크린샷 아트워크 방송 동영상 창작마당 뉴스 가이드 평가

Space Engineers

상점 페이지
Space Engineers >  창작마당 > Spite 님의 창작마당
26 평점
ISL - Myxini Tunnel Miner MK3-AO 880
설명 토론0 댓글3 업데이트 노트
   
어워드
즐겨찾기
즐겨찾기됨
즐겨찾기 해제
Type: Blueprint
태그: ship, small_grid, safe
파일 크기
게시일
업데이트일
4.005 MB
2020년 5월 17일 오전 10시 35분
2021년 4월 28일 오전 8시 35분
업데이트 노트 5개 (보기)
필요한 DLC
이 아이템은 여기 있는 모든 DLC가 필요합니다
Space Engineers - Decorative Pack
필요한 아이템
이 항목에 필요한 다른 항목
제작자
Spite
오프라인
Spite와 다른 사용자들이 만든 모음집 391개 모두 보기 (숨긴 상태 몇 개 있을 수 있습니다)
2,184 순 방문자 수
4,880 현재 구독자 수
44 현재 즐겨찾기 수
이 아이템을 사용하려면 DLC가 있어야 합니다.

다운로드 위해 구독하기
ISL - Myxini Tunnel Miner MK3-AO 880

Spite님의 3 모음집
ISL - Small Grid Printable Ships (with Printer)
아이템 185개
ISL Shipyard
아이템 218개
ISL - Small Grid Miners
아이템 60개
설명
Purpose
A medium miner designed for tunneling horizontally or diagonally either manually or with the PAM autominer script.

The MK3 is available in all three thrust types, either as Agna (Basic Cockpit) or Myxini (industrial Cockpit) variants and features 4 connectors (allowing for varied docking options), a larger drill profile than the MK1 and MK2 Tunnel miners, and a stone ejection system.

The Hydrogen version can be used on moons but is not recommended for planets.

Features
Tools, Scripts & Weapons:
PAM Autominer script
Fancy Status Displays script
4 forward facing drills

Power:
7 Large Batteries

Movement & Control:
1 Cockpit
1 Remote Control
4 Gyroscopes
10 Large Atmospheric Thrusters
30 Small Atmospheric Thrusters

Cargo Space
4 Medium Cargo Containers
4 Connectors
4 Drills

Miscellaneous:
4 Cameras - Po, Sb, Rear, Underside
1 Ore Detector
1 Sensor (for use with PAM)
2 Spotlights
Repair Projector

This ship has an empty mass of 81341 kgs, and can move with a full cargo at a maximum tilt of 90 degrees below horizon, but cannot fly upside down.

All Programmable blocks are turned off in this blueprint and all toolbars are the same from the cockpit and remote control.

All ships in this set have a rear mounted Merge block and can be printed using a welder wall with one (large grid) piston.

Toolbars
Toolbar 1
1. Thrusters All On
2. Thrusters All Off
3. Thrusters Braking On
4. Thrusters Braking Off
5. Lights On/Off
6. Connectors Switch Lock
7. Camera Port
8. Camera Starboard
9.

Toolbar 2
1. Battery Discharge
2. Battery Recharge
3.
4. Camera Underside
5. Camera Rear
6. Drill Control
7. Drills On/Off
8. Ore Detector On/Off
9. Antenna Broadcast On/off

Toolbar 3
1. PB [PAM] "up"
2. PB [PAM] "down"
3. PB [PAM] "apply"
4. Ejector System On/Off
5. PB [PAM] "Align"
6. PB [PAM] "homepos"

Toolbar 6
1.
2.
3.
4.
5. Repair Projector On/Off
댓글 3개
< >
omni 2023년 7월 22일 오전 9시 11분 
so his problem might be caused by having thrusters on as when they are on they cause it to clang out or atleast that is what i have found when printing it
Spite  [작성자] 2021년 1월 9일 오후 8시 21분 
Thanks GuitarEC, glad you like the design.

As for your printing problem, the welder wall is definitely big enough.

are you printing layer by layer? This can be done using butting for increasing and decreasing minimum distance on the piston. This has been the only reliable way for me.

Or are you letting the piston retract all the way in one go? No matter how slowly, this usually leaves out some blocks, especially in the more complex designs
GuitarEC 2021년 1월 9일 오후 7시 48분 
I love the design, but it was a real bear to print for some reason - lots of blocks that didn't print, and I had to follow behind and manually weld things - sometimes having to grind out surface armor to get to inner areas (gyros, projector, etc). FYI - my printer is a 5x3 grid, piston travel is only 0.15 m/s.